Soffit & Fascia in
Sherwood Park, Alberta.
Pre-finished aluminum soffit and fascia with the attic intake ventilation actually calculated, and the blocking behind the panels opened so the airflow is real. On Sherwood Park homes this is usually the fix for a winter ceiling stain.
Free Soffit & Fascia Estimate
Get your Sherwood Park quote.
Free, no obligation, and priced on your actual Sherwood Park home. We reply the same day.
We come out to your Sherwood Park address, take a proper look at what you actually have, and put a real number in writing. No obligation, no sales pitch, and we get back to you the same day.
Or call (780) 937-1184Soffit & Fascia in Sherwood Park
What Sherwood Park actually needs from a soffit & fascia job.
Here is the pattern we find over and over in the older parts of Sherwood Park. A 1978 bungalow in Mills Haven or Glen Allan has had its attic insulation topped up two or three times over the decades, each time by blowing more in from the hatch. Every one of those top-ups pushed a little more insulation toward the eave. Forty years later the soffit looks immaculate from the driveway and the intake vents behind it are completely packed shut. The attic has stopped breathing, and nobody can see why.
That single failure causes more winter grief in this community than damaged shingles do. Blocked intake means the attic cannot flush the moisture your household produces, so it condenses as frost on the cold roof deck through a cold snap and comes through the ceiling when we get a thaw. It also means shingles cook from underneath in July, which is why an under-ventilated roof reaches the end of its life years early.
The newer Park has a different version of the same problem. On homes in Summerwood, Emerald Hills and Cambrian we regularly find perforated soffit panels installed over solid sheathing that was never cut open behind them. The panels are vented. The building is not. Alberta code asks for at least 1/300 of the insulated ceiling area in net free vent area, split roughly half intake and half exhaust, and we calculate that rather than counting panels.
About Sherwood Park
Sherwood Park started life in 1953 as a private development called Campbelltown, laid out for workers at the refineries east of Edmonton. Canada Post rejected the name in 1956 and it became Sherwood Park. Seventy years of building since then have left the community with an unusually wide spread of housing eras, from post-and-beam bungalows on generous mature lots to 2024 two-storeys with sixteen-foot gables, and roofs from every one of those decades sitting side by side on the same street.
Where We Work
Sherwood Park neighbourhoods we work in.
We have done soffit & fascia work across Sherwood Park, from the established streets in Glen Allan, Mills Haven, Broadmoor to the newer builds in Cambrian, Hearthstone, Bremner.
Our Standard
What every Sherwood Park soffit & fascia job includes.
Soffit and fascia get treated as trim, and they are actually the intake half of your attic ventilation system. Every cubic foot of air that leaves at the ridge has to enter somewhere, and it enters through the soffit. Get that wrong and the attic stops breathing, which is how you end up with attic rain in February and shingles that age from underneath. We install pre-finished aluminum with the vented area properly proportioned, and we open the blocking behind it so the airflow is real rather than decorative.
Vented soffit sized to the code
Alberta requires at least 1/300 of insulated ceiling area in net free vent area, split roughly half intake and half exhaust. We calculate the intake rather than guessing at panel count.
Blocking opened behind the panels
Perforated soffit installed over solid sheathing that was never cut open ventilates nothing. We check, and we open it.
Pre-finished aluminum
Baked enamel finish that holds colour, will not rot, and does not need painting. Colour matched to your fascia, eavestrough and trim.
Fascia over sound wood
Aluminum fascia capping is only as good as the board behind it. Rotten fascia gets replaced, not wrapped over, because wrapping rot just hides it.
Tight mitred corners
Corners cut and folded properly rather than butted and caulked. It is the detail that separates a finished eave from a patched one.
Baffles at the eave
Rafter baffles so blow-in insulation cannot drift into the eave and seal the intake shut, which is the single most common ventilation failure we find.
Bird and pest exclusion
Gaps at the eave closed properly so squirrels, birds and wasps are not using your soffit as a front door.
Done with the eavestrough
Fascia, soffit and eavestrough share the same access. Doing them together typically costs 10 to 15 percent less than separate visits.
Sherwood Park Pricing
What this costs in Sherwood Park.
Real 2026 ranges for the Edmonton region. Your written quote gives you a firm number after we have been on site, because a price without an inspection is a guess.
Aluminum soffit and fascia
$12 – $25 / linear ft
Installed, both items, pre-finished aluminum
Single-storey home
$2,200 – $5,500
Roughly 120 linear feet of each
Rafter baffles / intake correction
$400 – $1,200
Clearing blocked soffit intake, per attic
Attic ventilation upgrade
$300 – $800
Added or corrected exhaust venting
Doing soffit and fascia together costs meaningfully less than doing them separately, because the access equipment and setup are shared. Rotten fascia board discovered during removal is replaced at cost and shown to you first. For the complete regional breakdown, see our Edmonton roof replacement cost guide.
Permits · Strathcona County
Do you need a permit in Sherwood Park?
Strathcona County does not require a building permit for maintenance work that leaves the use, height and gross floor area of the building unchanged, which covers straight like-for-like re-shingling and re-siding. A permit is required for roof redesign, height changes, replacing damaged framing, adding dormers, or mounting rooftop equipment. We confirm the position with County Planning and Development on every job and handle the application when one is needed.
Strathcona County Planning and Development can be reached at 780-464-8080.
FAQ
Sherwood Park soffit & fascia questions.
You cannot tell from the ground, which is exactly the problem. It takes someone in the attic with a light checking whether airflow and daylight reach the eave in each rafter bay. On the 1970s and 1980s homes in the older Park, with decades of insulation top-ups, we find intake blocked far more often than not. The check is free and it is the first thing we do.
In most Sherwood Park cases, yes, in combination with air sealing the ceiling plane. Clearing blocked intake, adding baffles and balancing the exhaust is what lets the attic flush moisture instead of storing it as frost. Clearing intake typically runs $400 to $1,200 and a ventilation upgrade $300 to $800, which is a fraction of the roof some homeowners get sold for the same symptom.
You can, but it is usually poor value. All three share the same access and setup, and doing them together typically costs 10 to 15 percent less than separate visits. If the eavestrough has real life left we will say so, but if it is coming up for replacement in the next few years, do it now while the crew is already at the eave.
Sometimes, if the soffit is sound aluminum with adequate vented area. But fascia usually rots because water has been getting behind it for years, and that same water has often been in the soffit cavity. We would rather open it, look, and tell you honestly than cap over a problem.
From the ground you cannot, which is the problem. The panels look perfect while blow-in insulation has drifted into the eave and sealed the intake from inside. It takes someone in the attic with a light checking whether daylight and airflow reach the eave. That is the first thing we look at, and it is free.
It is the most common cause we find. Blocked intake stops the attic flushing moist air, so the moisture your household produces condenses as frost on the cold roof deck through a cold snap and melts through your ceiling when it warms up. Clearing the intake and adding baffles fixes more attic moisture problems than anything else we do.
More in Sherwood Park
Everything under one roof.
Roofing in Sherwood Park
From the mature bungalows of Glen Allan and Mills Haven to the new two-storeys going up in Cambrian and Bremner, we have re-roofed across Strathcona County long enough to know what each era of Sherwood Park house needs and what it will throw at us once the shingles are off..
Roof Repair in Sherwood Park
Storm damage, ice at the eaves, and leaks that turn out to be somewhere other than the ceiling stain.
Siding in Sherwood Park
Cedar and hardboard from the eighties that has finally given up, tired vinyl from the nineties, and new builds where the flashing details matter more than the panel.
Eavestrough in Sherwood Park
Seamless 5-inch and 6-inch aluminum formed on site at your Sherwood Park address, pitched so water actually moves, and sized for the roof area feeding it rather than for whatever happened to be there before..
Worth Reading
