Siding in
Spruce Grove, Alberta.
Nineties vinyl that has gone brittle, seventies cladding that is finally done, and new builds on exposed lots where how the siding is hung matters as much as what it is. We re-side across Spruce Grove.
Free Siding Estimate
Get your Spruce Grove quote.
Free, no obligation, and priced on your actual Spruce Grove home. We reply the same day.
We come out to your Spruce Grove address, take a proper look at what you actually have, and put a real number in writing. No obligation, no sales pitch, and we get back to you the same day.
Or call (780) 937-1184Siding in Spruce Grove
What Spruce Grove actually needs from a siding job.
Wind exposure is the deciding factor for siding out here, and it exposes installation shortcuts faster than anywhere else we work. Vinyl siding must be hung, not fastened tight: the panels need to slide as they expand and contract through a 60-degree annual temperature swing, which means fasteners centred in the slots and left slightly loose. Installed tight, a wall buckles in July and works its nails loose in January, and on a west-facing elevation in Copperhaven or Harvest Ridge the wind finds every loosened panel. Most of the failed vinyl we replace in Spruce Grove failed this way rather than from age.
That same exposure is why we recommend LP SmartSide to more homeowners here than almost anywhere. Vinyl loses impact tolerance below about minus 20, and a west-side wall out here takes wind-driven ice and hail with nothing to break it up. Engineered wood keeps its toughness in the cold, comes in 16-foot lengths so there are fewer seams across a long exposed wall, and can be repaired and repainted rather than requiring a colour-matched panel that may be discontinued in a decade.
In the older core, Millgrove, Broxton Park and Woodhaven, the job is a straightforward tear-off of 1970s and 80s cladding, and the interest is behind it. We check the roof-to-wall junctions carefully, because kick-out flashing was not standard practice then, and any bonus room or attached garage roof running into a wall has spent forty years directing runoff into an assembly nobody can see.
About Spruce Grove
Spruce Grove has grown faster than anywhere else around Edmonton, adding roughly 15 percent to its population in five years, and the building has all pushed west and north into open farmland. It also has one of the region's more useful local quirks: streets within each subdivision all begin with the same letter, so Millgrove is all M streets and Jesperdale is all J. What it means for us is a city split cleanly between a 1970s and 80s core with settled trees and a wide belt of exposed new construction facing the prairie wind.
Where We Work
Spruce Grove neighbourhoods we work in.
We have done siding work across Spruce Grove, from the established streets in Millgrove, Broxton Park, Woodhaven to the newer builds in Copperhaven, Harvest Ridge, Easton.
Our Standard
What every Spruce Grove siding job includes.
Siding is the part of the exterior people judge from the street and the part that quietly decides whether your walls stay dry. We install vinyl, LP SmartSide engineered wood and James Hardie fibre cement, and we build what goes behind them properly: a correctly lapped water-resistive barrier, head flashing over every opening, sill pans below, and kick-out flashing wherever a roof edge meets a wall. That last piece of metal is small, cheap and the most commonly omitted detail in residential construction.
Full tear-off and inspection
Old cladding comes off so we can see the sheathing. Rot found behind siding is common and it is always cheaper to deal with while the wall is open.
Proper water-resistive barrier
House wrap lapped shingle-style so water runs down and out rather than into the laps, taped at seams and penetrations.
Flashing done right
Head flashing above every window and door, sill pans below, and kick-out flashing where roof meets wall. Skipping the kick-out is how walls rot invisibly for years.
Vinyl siding
Hung correctly with fasteners centred and left slightly loose so the panels can move through a 60-degree annual temperature swing without buckling or pulling.
LP SmartSide engineered wood
Our most-recommended option here. Real wood texture, far better cold-weather impact resistance than vinyl, long 16-foot lengths, repairable and repaintable.
James Hardie fibre cement
The premium choice. Dimensionally stable, non-combustible, excellent impact resistance, and factory ColorPlus finish that holds colour for decades.
Trim, corners and details
Tight mitres, proper corner posts, and clean transitions at stone, soffit and roofline. This is where a siding job either looks finished or does not.
Clearances that matter
Siding held off grade, off roof decks and off horizontal surfaces so it is not wicking water at the bottom edge.
Spruce Grove Pricing
What this costs in Spruce Grove.
Real 2026 ranges for the Edmonton region. Your written quote gives you a firm number after we have been on site, because a price without an inspection is a guess.
Vinyl
$5 – $10 / sq ft
Typical full re-side $12,000 – $22,000
LP SmartSide
$9 – $15 / sq ft
Typical full re-side $20,000 – $34,000
James Hardie
$10 – $18 / sq ft
Typical full re-side $24,000 – $45,000
Cedar
$15 – $25 / sq ft
Beautiful, and the highest maintenance option here
Ranges assume roughly 2,000 to 3,000 square feet of wall area and include tear-off, house wrap, trim and flashing. Storeys and scaffolding, window and door count, gables and dormers, and any rot found behind the old cladding all move the number. For the complete regional breakdown, see our Edmonton roof replacement cost guide.
Permits · City of Spruce Grove
Do you need a permit in Spruce Grove?
Spruce Grove follows the same regional pattern: a like-for-like re-shingle or re-clad is maintenance and does not require a building permit, while structural work, changes to roof shape or height, added floor area, or repairs following fire or flood do. Many of the newer subdivisions also carry architectural controls through the developer, which we work within. We confirm both before starting.
FAQ
Spruce Grove siding questions.
For a home with roughly 2,000 to 3,000 square feet of wall, vinyl runs about $12,000 to $22,000, LP SmartSide $20,000 to $34,000, and James Hardie $24,000 to $45,000, including tear-off, house wrap, trim and flashing. Two-storeys in the newer subdivisions sit higher because of scaffolding and the number of gables and openings.
Usually it is not age, it is how it was hung. Vinyl needs to slide freely as it expands and contracts, and if the fasteners were driven tight the panels buckle when they expand and work loose when they contract. On the exposed lots in Spruce Grove that shows up as rattling and eventually as panels coming off. Sometimes a section can be re-hung correctly. Where it is widespread, replacement is the honest answer.
Frequently, yes. Copperhaven, Harvest Ridge, Easton and several other newer areas carry developer architectural controls governing exterior materials and colours. We work within them routinely. Send us whatever guidelines you received at purchase and we will make sure the specification complies before any material is ordered.
For most homes here, LP SmartSide. Vinyl gets brittle below about minus 20 and cracks from impacts it would shrug off in summer, while engineered wood keeps its impact resistance in the cold, looks like real wood, and is repairable. James Hardie is the premium answer if you are staying long-term or the elevation takes hard weather.
We do not recommend it. Going over the old siding means nobody ever sees the sheathing or the water barrier behind it, and hidden rot is common, particularly below windows and wherever a kick-out flashing was omitted. Tear-off costs more up front and is the only way to know what you are building on.
Replacing exterior finish with similar material is generally treated as maintenance across the Edmonton region and does not require a building permit. Changing the exterior in a way that affects the structure, or work on a property with architectural controls, can be different. We confirm the requirement for your address before we start.
More in Spruce Grove
Everything under one roof.
Roofing in Spruce Grove
From the 1970s core in Millgrove and Broxton Park to the new two-storeys going up in Copperhaven, Easton and Fenwyck, we know what a Spruce Grove roof faces out here on the open west side..
Roof Repair in Spruce Grove
Wind-lifted shingles, hail from the 2026 storm season, and leaks that need diagnosing rather than patching.
Eavestrough in Spruce Grove
Seamless aluminum formed at your Spruce Grove address, sized for the roof draining into it, and pitched so nothing stands and freezes.
Soffit & Fascia in Spruce Grove
Aluminum soffit and fascia with the attic intake ventilation properly calculated and the blocking opened behind it.
Worth Reading
